Our Free Study Guides and Practice Exams Will Make You Certifiable!
  Home

HOME | EXAM DETAILS | FREE TESTS | STUDY GUIDES | GLOSSARY | ARTICLES | BOOKS & TRAINING | FORUMS | CAREER & JOBS
 MICROSOFT
 COMPTIA
 CISCO
 CIW
 LPI
 RED HAT
 IBM
 FREE MAGAZINES
 WHITE PAPERS
 TOPSITES
 CONTRIBUTORS
 SITE MAP
 SITE FAQ
 

Users online
total users: 343

Last Post
New opportunities
by Kjell
Jan. 05, 2009 22:55

Board statistics
We have a total of 83435 posts!
 TechTutorials
 CertifyPro
 Certnotes
 Web Host Reviews
 CBT Training
 MCSE Boot Camp
 MCSE Training


<< Index | Next >>

SCSI
SCSI stands for Small Computer Systems Interface and is a less commonly used, but faster alternative to IDE. Another advantage of SCSI is that only the controller uses an IRQ while the devices attached to it do not. SCSI devices are most commonly found in servers and high-end workstations.

SCSI devices, such as hard drives and CD-ROM drives, plug into a SCSI controller internally or externally, and multiple devices can be configured in a chain. Internal devices connect using a 68-pin ribbon cable that is similar to that used for IDE devices. It is very important that you get the pin orientation correct when installing a SCSI drive. Failure to do so can destroy the SCSI device and/or the SCSI controller card. External devices connect to the SCSI controller on the back of the PC. To learn more about the various cable and connector types, read SCSI Connector Types.

In order for the SCSI bus to work correctly, the last device on any SCSI chain must be terminated. Some SCSI devices are self-terminating, while others can be terminated using jumpers or a resistor that plugs into the end of the cable or device.

Each device on a SCSI chain must receive its own SCSI ID including the controller. This ID can be set on SCSI devices using either jumpers, dip switches or dials. You will need to consult with the manufacturer of your device to figure out the correct method for setting the ID. New SCSI standards support up to 16 devices. The controller is usually preset to receive ID 7. A bootable hard drive would usually be set to ID 0 since it is the lowest on the list and the first to be accessed.

SCSI controllers come with their own BIOS that offer configuration settings.

Over the years, there have been a number of SCSI standards and increasing speed. The table below shows the details of the various SCSI standards:

Standard Bus Speed (MBps) Bus Width Devices Supported
SCSI-1 5 8 8
Fast SCSI 10 8 8
Fast Wide SCSI 20 16 16
Ultra SCSI 20 8 8
Wide Ultra SCSI 40 16 16
Ultra2 SCSI 40 8 8
Wide Ultra2 SCSI 80 16 16
Ultra3 SCSI
(Ultra 160)
160 16 16
Ultra320 320 16 16

Additional Reading
http://www.techtutorials.com/Hardware/SCSI/

<< Index | Next >>



 CareerAcademy
Certification training videos with private instructors. Topics cover Microsoft MCSE, CompTIA, CISSP & Cisco exams. Courses also come with official practice exams with 7x24 mentors.
more products...
 Netwind Learning
Free Demo. Certification Training for A+, MCSE, MCTS Microsoft.NET, Cisco CCNA, CCNP, CCVP, CCSP, Java, Oracle, Linux, PMP and 100's of other courses.
more products...
 EDULEARN
Certification Training on CD-ROMs & Videos: Microsoft MCSE Training, A+ Certification, Windows 2003, & Free demos. MCSE certification training includes videos and labs.
more products...
 Training Planet
Nationwide Computer Training Boot Camp Classes and also CD based training courses A+ Certification, Cisco Training, MCSE, CISSP, Autocad, Office, PMP, SOX, PC Diagnostics
more products...


ADVERTISE | PARTNERSHIPS | PRIVACY POLICY | DISCLAIMER | | CONTACT


IT Showcase