Our Free Study Guides and Practice Exams Will Make You Certifiable!
 Home

HOME | EXAM DETAILS | FREE TESTS | STUDY GUIDES | GLOSSARY | ARTICLES | BOOKS & TRAINING | FORUMS | CAREER & JOBS
 MICROSOFT
 COMPTIA
 CISCO
 CIW
 LPI
 RED HAT
 IBM
 FREE MAGAZINES
 WHITE PAPERS
 TOPSITES
 CONTRIBUTORS
 SITE MAP
 SITE FAQ
 


Users online
total users: 365

Last Post
70-290 Exam Format
by hnic2k7
Aug. 08, 2008 13:51

Board statistics
We have a total of 81006 posts!
 TechTutorials
 CertifyPro
 Certnotes
 Web Host Reviews
 CBT Training
 MCSE Boot Camp
 MCSE Training

EIGRP And Split Horizon

EIGRP is a major topic for your CCNA and CCNP studies, and one basic skill you'll need to pass your Cisco certification exams is to identify situations where you need to enable or disable split horizon. EIGRP commands tend to be a little different than those used with other protocols, so let's take a look at how EIGRP and split horizon interoperate.

R1 is our hub router, with R2 and R3 as the spokes. There are no subinterfaces, and each router is advertising a single loopback network using its router number for each octet. R1 will see both R2 and R3's loopback network, but the spokes will not have a route to the other spoke's loopback. "show ip route eigrp" verifies this.

R1#show ip route eigrp

2.0.0.0/32 is subnetted, 1 subnets

D 2.2.2.2 [90/2297856] via 172.12.123.2, 00:03:29, Serial0

3.0.0.0/32 is subnetted, 1 subnets

D 3.3.3.3 [90/2297856] via 172.12.123.3, 00:03:29, Serial0

R2#show ip route eigrp

1.0.0.0/32 is subnetted, 1 subnets

D 1.1.1.1 [90/2297856] via 172.12.123.1, 00:05:20, Serial0

R3#show ip route eigrp

1.0.0.0/32 is subnetted, 1 subnets

D 1.1.1.1 [90/2297856] via 172.12.123.1, 00:07:54, Serial0


EIGRP runs split horizon by default, making it impossible for R1 to forward an advertisement to R2 regarding R3's loopback. Likewise, R1 cannot advertise R2's loopback address to R3. We could configure two subinterfaces on R1 to resolve this issue, but here we're going to disable split horizon instead.

R1(config)#int serial0

R1(config-if)#no ip split-horizon ?

eigrp Enhanced Interior Gateway Routing Protocol (EIGRP)

<cr>

R1(config-if)#no ip split-horizon eigrp ?

<1-65535> Autonomous system number

R1(config-if)#no ip split-horizon eigrp 100

04:10:02: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.2 (Serial0) is down: split horizon changed

04:10:02: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.3 (Serial0) is down: split horizon changed

04:10:25: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.2 (Serial0) is up: new adjacency

04:10:37: %DUAL-5-NBRCHANGE: IP-EIGRP 100: Neighbor 172.12.123.3 (Serial0) is up: new adjacency


Note that disabling split horizon resulted in the EIGRP adjacencies being torn down. They came back up 20 - 35 seconds after being torn down according to the timestamps, but that's a good detail to keep in mind!

The routing tables of each spoke should now show the loopback network configured on the remote spoke.

R2#show ip route eigrp

1.0.0.0/32 is subnetted, 1 subnets

D 1.1.1.1 [90/2297856] via 172.12.123.1, 00:00:02, Serial0

3.0.0.0/32 is subnetted, 1 subnets

D 3.3.3.3 [90/2809856] via 172.12.123.1, 00:00:02, Serial0

R3#show ip route eigrp

1.0.0.0/32 is subnetted, 1 subnets

D 1.1.1.1 [90/2297856] via 172.12.123.1, 00:00:02, Serial0

2.0.0.0/32 is subnetted, 1 subnets

D 2.2.2.2 [90/2809856] via 172.12.123.1, 00:00:02, Serial0


Be careful when disabling split horizon. In this scenario, R1 can and will advertise routes out Serial0 that were learned about on that interface in the first place, and that's not always desirable. Split horizon is enabled by default for a reason, so be careful when disabling it!

About the Author:
Chris Bryant, CCIE #12933, is the owner of The Bryant Advantage , home of free CCNA and CCNP tutorials! Pass the CCNA exam with Chris Bryant!


 CareerAcademy
Certification training videos with private instructors. Topics cover Microsoft MCSE, CompTIA, CISSP & Cisco exams. Courses also come with official practice exams with 7x24 mentors.
more products...
 Netwind Learning
Free Demo. Certification Training for A+, MCSE, MCTS Microsoft.NET, Cisco CCNA, CCNP, CCVP, CCSP, Java, Oracle, Linux, PMP and 100's of other courses.
more products...
 EDULEARN
Certification Training on CD-ROMs & Videos: Microsoft MCSE Training, A+ Certification, Windows 2003, & Free demos. MCSE certification training includes videos and labs.
more products...
 Training Planet
Nationwide Computer Training Boot Camp Classes and also CD based training courses A+ Certification, Cisco Training, MCSE, CISSP, Autocad, Office, PMP, SOX, PC Diagnostics
more products...


ADVERTISE | PARTNERSHIPS | PRIVACY POLICY | DISCLAIMER | | CONTACT


IT Showcase